I’ve been sidelined by a knee surgery. I’ve had an issue for a while (over a year) and I decided it was finally time to get it sorted out. So while I convelese, I thought I’d put up a post detailing what I believe to be a mostly concise list of repairs that are required on the Big White Bus. We are getting another round of stimulus money from the O’Biden administration. And why not spend it on my Land Rover? Let’s get started:
You’ve read my mis-adventures with my ignition system (Okierover). I mostly attempted to replace the entire system with GM off the shelf parts. In the end I could not stop the ignition modules from overheating. This leads to them failing basically every two weeks. With “lifetime warranty” I only bought the part twice. And when I was completely convinced I would either have to drive in the right lane, everywhere, or doing something else, I had trained myself to change the module in less than two minutes. Standing on the side of I-35 during rush hour traffic every two weeks for 4 months is not among the smartest things I’ve ever done.
At this point I’ve decided that I will replace the entire ignition system with an after-market version. I haven’t picked that version yet, but know it will be my first repair. This means the distributor, ignition coil, modules, all of it will be replaced. I currently have a “Lucas”1 setup. I don’t believe it is reliable. I have driven her with this setup, but I’m not convinced it is safe.
Once again I am faced with a failed alternator. I have written many times about the alternator issues (Okierover). I bought the NAPA alternator back in 2005. I have replaced it under warranty 6 times (with 7 coming). Sometimes you can’t beat a NAPA warranty, even if the part only lasts about 2-3 years before it fails. It still surprises me that an OEM alternator from the factory lasted 15 years but a replacement part would not give me 2 years of service.
The BWB has a slow battery drain, I suspect it is the diode pack as it was three times before. Once a diode fails, it’s over. The alternator will still charge, but it will also discharge the battery when the engine is off. If you still have any of your hearing left, you can hear tell-tale ultra high pitch sound coming from the back of the alternator when the engine is off.
Heater Fan Blower Motor
This repair is in progress, you’ve seen the posts (Okierover). All that is left is to source the new hoses and the foam gasket sets and such. I broke a couple of plastic bits and found a great source for spares in Matt Gaum (Roadside Werx) Some of these plastic bits are starting to become unobtainium.
This leads me to contemplate 3D printing of these parts. I’ll look for a 3d printer and do some research into the types of plastics that might work best. I’m a little surprised I haven’t seen someone doing this already. If you have, leave us a link in the comments.
At some point the bushing on the steering shaft has slipped. I need to pull it all out and get it corrected. It is not dangerous, it’s just annoying.
Rear Compartment Tie-Downs
I can’t believe I’ve driven around with a hundred plus pounds of tools and spares NOT tied down in the back of my rig. I have only avoided an epic stupid mistake because I’m a hell-of-a-driver and have avoided serious accidents.
Nice to Have
Now let me talk about what we in the Project Management game call, “Nice to Have’s”.
I have researched a replacement system that I think will be great. When I buy it I’ll do a full write up. Bluetooth…backup camera… Van Halen “Eruption” or Wagner’s “Die Walküre” at 120dB depends on your situation.
This probably shouldn’t be a nice to have. I live in the southern plains and I promise it gets hot here. This is more than likely going to be a must have/critical. This system is a total loss. I will have to replace EVERYTHING including hoses. The testing for leaks will need to be epic if this is going to be a long term solution.
Power Steering Leak
I STILL have a power steering leak. After all my issues with leaking steering boxes you’d think this wouldn’t plague me. You’ve seen where I bought a rebuilt steering box (Facebook) from Carsteeringwholesale.com (NOT RECOMMENDED, DO NOT TRUST). I received the steering box from them and it was leaking out of the box. I fussed and yelled at them to no avail and they sent me a replacement (that I had to pay shipping on) that leaked EVEN WORSE than the shitty one they sent me to start with. Buyer beware.
I have another slow leak and will at some point need to replace this pump too.
My left front hub assembly is leaking. I’m not sure which part has the leak. I’ll have to find it eventually and replace the seal or brake caliper, or whatever it is.
Gas Gauge Uncertainty
When I replaced my last fuel pump (Okierover) I managed to get the float out of sorts and its basically a mystery as to how much fuel I have in the tank at any time except when I fill it. I need to get in there and futz with the level and see if I can fix that.
I would LOVE to have new rugs. Maybe a proper steam cleaning would do the job, I don’t know.
I have looked at a lot of seat covers. I think I’m leaning toward a NON-Leather cover. Leather covers are readily available and modestly priced. I just think I can get a more durable, no maintenance option sourced that wouldn’t make me cry a little bit inside each time I slide into the BWB with mud all over me or soaking wet. Oklahoma summers are not kind to old leather.
I don’t need gangster dark tint. I think a tint one these plethora of windows would go a long way toward keeping me cool in the summer.
The BWB is losing her clearcoat. And the vinyl D pillars are quite knackered. In a perfect world with everything else repaired, I’d probably throw some paint on her.
I have a mouse somewhere in the truck. I noticed some evidence of a mouse making its home inside. I couldn’t blame them with -14F this winter. Car spiders (Okierover) are one thing, I can’t have mice.
1: The name Lucas can be licensed by just about anyone wanting to use their name. The last set of “Lucas” parts I got were made in China….CHINA. You should not associate quality replacement parts to anything made in China.
Never fear… I have not let my wrenching skills go to waste. I helped my dear friend Eric and his son Vallie change the plugs and coils on their 2000 Jaguar S-type. We had a great afternoon. And it was a fine example of no matter what you think a job will entail…something will go wrong and will require a part no one has in stock.
Pro Tip: Jaguar (Ford) coolant hose “T”s are made out of some form of plastic-mache and hope.
Thanks for reading and Happy Rovering