Uncategorized

December 11, 2023December 11, 2023

Fixing the D Pillar Rust (Post #634) 12/11/2023

If you follow the blog you have seen the rust damage from open cell foam in the upper D Pillar. The foam got wet and over time ate through the pillar and caused a hole that allowed water into the rear. It wasn’t likely a “stream” of water as the pillar had a cover and the foam also blocked the hole.

In any event, it had to be repaired. I went to some effort to research the removal of the rear quarter panel windows. Damaging the seal is a non-starter. Replacement seals cost in the neighborhood of $500.00(US). And there is also a chance of breaking a window.

I had the Evil German Dude over for Thanksgiving and showed him the damage. He was pretty certain that I could weld a patch there WITHOUT removing the seal and window. Using caution and allowing time for the welds to cool, he was sure that the welding would not be a problem.

Trusting he was right, I proceeded to build a patch and weld it in. The patch was pretty easy to make. You’ll need a bench vise or a metal brake to bend the steel. Well…if you have to bend steel for your patch. I got the patch in place, wire wheeled the paint and primer away and started welding.

My first welds didn’t stick. I had to work through that. Some of the issue was a crappy ground point. The other could be paint I hadn’t removed. I finally sorted that out and made the weld around the piece. I will come back with some seam sealer and make sure there are no holes by sealing them with a bead of sealant.

I was a bit surprised at how well this went. I was expecting a much more complicated repair. I’m not in love with the welds. But such is the way you have to weld thin steel. They also are not in sight so they didn’t have to be pretty…and they aren’t pretty.

The temp cooled off this week. It was 40F degrees when I finished up. Funny how two and a half months ago the temp was three times that in the shop. We got a little reprieve on Sunday and it got above 50F degrees.

I’ve been kicking around an idea if the window had broken. Building in wing window storage boxes. I could use them to pass through power to solar panels, shore power, a heating tube for a propane heater, and the most exciting, water for showers and cooking/washing hands and such. I’ve got the bug so I may build a mockup with cardboard to see if it would work the way I’m thinking. It’s maybe a project for another day. You can check out this video which served as a good portion of the inspiration. Dirt Lifestyle has two videos on gullwing windows for his Discovery II. This is the latest [YouTube], and is an improvement of the original, enjoy.

I hope you enjoy the video of my work. Like and subscribe and if you want to help through a recurring contribution, Patreon is helpful way to do that.

Thanks for reading and Happy Rovering.

September 18, 2023September 19, 2023

The Big White Bus Will Not Start (Post #624) September 18, 2023

Well, awesome. The Big White Bus won’t start.

I have fired it up once since I parked it in my newly constructed shoppe 5 years ago. I guess I should have expected there would be “issues”. But I wasn’t expecting the issue to be this one.

Mr. Fisher came over and we diagnosed the issue. We started with checking the power at the pump. As you may be aware, when you turn the key over it powers the pump briefly. So if you just “turn on the key” and go back there to check the voltage you won’t find any. That’s why it takes either some seriously creative use of a volt meter or you get one of the bestest friends to come over and turn the key for you. We had voltage all the way through the wiring harness.

We then confirmed we have spark from the ignition system. I pulled the number 1 plug and with a screwdriver I grounded it and watched for spark. You can buy a fancy spark tester, matter of fact I think I own one. I have no idea where it is though. Spark confirmed.

So we have two of the three things (Meatloaf would say that “ain’t bad”) to make the vehicle run. Air and Spark. Now why aren’t we getting fuel.

I pulled the gas line off at the regulator on the back side top of the engine and had Mr. Fisher crank the ignition. We should have had gas squirting out if it worked. It did not. This fit with me NOT hearing the pump run when the ignition was turned over.

The only thing left was to pull the fuel pump and do a visual inspection. What I found was not expected. I said, “Wow.” a lot in the video. There were several parts that were obviously degrading due to being submerged in petrol for so long. There was visible rust on the steel parts as well. Generally the pump was in a terrible state. I was not aware that petrol would do that to those parts. The only gas I ever put in my Classic is 100% real gas, unless I am in Texas where they only sell ethanol (at least the last time I was buying gas there). You would expect ethanol to eventually separate and turn to water. You can read all about that on the Road Guardians website.

I will be replacing the fuel pump and have ordered the part from Atlantic British. I found some that were cheaper on Amazon. But my skepticism and need to have it delivered before next October weighed heavily on my decision where to purchase. The pictures all looked like the pumps were manufactured in the same place. Same white plastic. Same blue plugs.

If you look on Amazon you’ll see the pumps look like the same ones. If I had unlimited funds or sponsorship, I’d buy one from everyone and do a side-by-side comparison.

All this “BUY IT NEW” has me thinking about what this would cost if we just fixed the pump. All you need to do is replace the pump in the collector can (that bottom part). I’ll do a post about that in the coming weeks.

So…do I drain the tank too? If the gasoline HAS turned to varnish I should probably put some treatment in there. I’m thinking I’m gonna add a silly amount of STP Fuel Injector cleaner in that tank. I can say, WHEN I get it running It will run for quite a while before I shut her down. I want to give the truck plenty of time to dislodge any crap in the fuel lines. I’m also guessing I’ll need to swap the fuel filter too.

If its not one thing, its another. It really, never ends.

Mr. Fisher also brought over his Viair Compressor. We spent some time looking at it and checking out all its features.

Thanks for reading and Happy Rovering.

September 5, 2023September 5, 2023

Fender Repair Part 5, MORE Crappy Welding of the Large Fender Patch (Post #622) September 2-3, 2023

In this installment I finish the left rear fender panel. And by finish I mean I had to completed replace the outer fender I had previously welded up. I added a strap to attach the inner fender to the outer fender.

The outer fender’s welds were compromised because I ran out of shielding gas halfway through. The panel was 16 gauge and I swapped it with an 18 gauge. The right thing to do was replace it and “do it right”.

Now, I’m no body man and right to me is probably not right to someone who actually knows what they are doing. As I mentioned in the video I need another 10 or 20 years of welding experience to be “competent”. Over all I’m a lot happier with this replaced panel. The 16 gauge panel would not have worked. It would not have been watertight no matter what I did.

I covered everything with yet another coating of primer. I also put seam sealer in the appropriate places. This only seemed prudent as I am almost certain this will rust again. My hope is it will take at least 20 years to rust out.

I thought some of the welding went a lot better than the previous attempts. I want to say, “I’m getting better.” but I’m pretty sure I’m fooling myself. Most people could probably weld if shown how and a little practice. Welding WELL however is really hard.

So add to the fact I’m saying welding is hard…and welding UPSIDE DOWN is another level. We did not go over this scenario in my class. I’m half tempted to take the class again and do the entire class upside down. I finally figured out the I could weld sideways that worked pretty good. Even with my new sideways technique it didn’t stop me from getting some new holes in my PPE and my skin from hot slag dripping down. My grandson Grady was horrified by the scab in the crook of my elbow. The chunk that got me on the chest made a similar hole there.

I also did quite a bit of cutting and the sparks flying back on me warmed me up a bit. Thankfully my Round House Overalls¹ deflected the sparks and only “warmed” my family package. If you remember this post from December 2010, “The one where I catch myself on fire in the furtherance of Land Rovering” [Okierover] I caught myself on fire cutting the passenger side floor panel. What I learned from that was:

Blue jeans are not safety gear and are a sad substitute for PPE.
Longjohns [IBC] (aka long handles [Collins], thermal underwear, etc…) will keep the flame off you for a brief time.
Your best friends don’t want you harmed, but also want to take videos of you when you are on fire so they can tease you later.

Thanks for reading and Happy Rovering

¹This is my unsponsored review of Round House Brown Duck Overalls. It is a solid 10 out of 10. They are made in Shawnee Oklahoma (Home of Brad Pitt) and at $60.00 a pair (on sale at the time of this posting) a real bargain.

August 17, 2023August 17, 2023

Fender Repair Part 3, Welding of the Large Patches (Post #619) August 12, 2023

Folks…its hot outside.

It is not uncommon for Oklahoma to have temps over 100°F for extended periods of time. Even when I was a kid this happened some summers. The hottest temp I ever remembered experiencing was 125°F during the Combined Arms Exercise (CAX) in August of 1985 while I was serving in the US Marine Corps Reserve. We spent 14 lovely days (without a shower) in the high desert of the Marine Corps Air Ground Combat Center, also known as 29 Palms [Marines.mil] or “the stumps” as many Marines sometimes fondly remember it.

I recently got to catch up with one of my friends that I had not seen since February of 1986. We talked for hours and brought up that summer and our exploits in the desert several times.

I know we are supposedly experiencing “never before” (not since records have been kept anyway) high temps across the entire earth. I heard a guy offer an alternative theory to the climate warming crisis. He said, “What if we have been living during a historically cold temperature all this time?” That does make you think a bit…

I work in the shoppe as long as I can during these hot days. The GoPro camera usually signals that I’m done when it over heats. The last few videos I have taken the GoPro it has prematurely quit and had to be set on the portable air condition to get it back to operating temperature.

After I’ve had enough with the heat, leaving the shop on these days in July and August on the Southern plains with triple digit temperatures has me feeling a bit like Sir Alec Guinness when he emerged from “the oven” in Bridge Over the River Kwai (1957).

https://youtube.com/clip/Ugkxpvg6PJsI2cItxKk5YIs2Qaf_1TQReYl5

For some stupid reason that video will not embed.

I’ve shown the shoppe temp in previous videos. When the outside temp is 100°F plus. The shoppe temp can easily be 110° to 120°F inside. It’s basically a giant tin oven. It desperately needs an exhaust fan to pull the hot air out. I will be sourcing one and getting it wired in as soon as my budget allows.

I’ve learned four very important lessons in my 58 years of life, that the wisdom of which needs to be passed on to others:

Communism doesn’t work.
Never get involved in a land war in Asia.
Never cook bacon naked.
And not the least of which is, don’t use an angle grinder with a cut off wheel to cut steel plate while wearing shorts and a short-sleeved t-shirt after you’ve had a couple of Cuba Libre’s.

While taking care to follow the “Safety Second” mantra, I cut the steel the night before after a crappy day at work. At least I wore my protective face shield and moved the steel stock away from flammables and the Big White Bus while I ~~showered the entire area including my arms and legs with blistering hot sparks~~ precisely cut the two patches.

I remembered to pack a pair of gloves and to place the fender patches in the Ford F-150 after I cut them Friday night. I was worried that in my haste to get to OKC to eat BBQ and see Mike (who is perhaps my oldest friend), I would miss out on my opportunity to manipulate steel plate using tonnes of pressure with the English Wheel because I left the steel at the Okierover Base Camp. Its happened before.

Thankfully I have awesome friends that have skills and tools I have yet to acquire. JagGuy has an English Wheel in his shop.

Image from TheShed.NZ How to Build Your Own English Wheel

An English Wheel [TheShed.NZ] which if you know anything about its function makes flat stock, curved. For the left rear fender, the last two pieces to weld up are two large arches. The first of which is the big hole in the wheel well, which is where one of the seat belt mounts (which I will have in place but will not use) go. The other is the outer wheel well arch against the outer wall.

I’m going to use his English Wheel to give my patches some curve (parabola) so they are easier to manipulate and weld into place. I’ve never used an English Wheel but am not afraid to try.

I know using the English Wheel is an “art” and people who can produce panels this way charge premium prices due to this highly skilled and labour-intensive production method. I’m not highly skilled and I don’t plan on doing anything that might pass for “labour-intensive”. Just a few tugs and pulls to get a curve. The wheeling will hopefully make my welding and fitting of the panels easier.

The temp actually cooled off for Saturday, apparently the “heat-bubble” popped. We had rain and temps in the 80s. You can watch the video of the wheeling process and the welding of the fenders.

Thanks for reading and Happy Rovering.

Mmmm welding

April 30, 2023May 16, 2023

Can we HAVE any more setbacks? (Post #609) 4/30/2023

Apparently, yes, yes we can.

So if you’ve been a fan and reader for very many years you have probably heard me refer to the Okierover Rules. There are a few rules I try to live my life by, let me hit the top three:

I will not live where I am not the highest tertiary consumer on the food chain.
I don’t play with electricity.
Don’t date girls with dagger tattoos.
There are others…but lets stop there.

Unfortunately for me, I bought a welder that requires a 208 volt plug. My shop is only wired for 110 volt. You know that saying from Mr. Mom (1983) starring Michael Keaton:

Well that’s about the sum of it. I’m just about that clueless when it comes to the magic of powering our homes and shops.

According to a review on InboxQ.com:

“The Pro MIG 180’s convenient switch knob easily allows users to choose between output levels. The 120-volt option allows you to connect to any household power source and is perfect for working on light steel and thinner metals like aluminum sheets. If you want to work on thicker metals, just flick the knob opt to change to the 208-volt/230-volt option.”

I must have missed that day in shop class when they explained how to wire 110V like 208/220V. And that’s another thing…I’ve been around a few years and never have I ever heard of 208V. So again, I’m sitting here thinking, “I wish Mr. Murr would have let me take shop class like all the other kids.” In his fine evaluation of my brain power, he thought I was better suited to “go to college”. I had to get special permission to enroll in Vo-tech! Electronics never-the-less. This was before the Personal Computer revolution (think Fall of 1980). I can tell you for certain, electronics was not an “easy” class. I had to work at it. And frankly, college was unaffordable for me. I went anyway, but let’s just say, the trades probably would have been a better idea.

I asked the Evil German Dude what he thought of the wiring in the shop. He DID indeed go the trades route and worked for the electric company in Germany as a young man and understands the magic of electricity about as well as anyone. Seriously one of the smartest people I know. He did not believe the wiring from the house to the shop would support 220V. So, it looks like I need to get a professional opinion and probably get a quote to get it upgraded.

Yay! more money I don’t have today.

So I know a lot of you are keen to see SPARKS flying and welding of rust panels and fixin’ them holes. As am I, I’m ready to see some return on investment for the welding class and the welder expenses, but this is going to be put off for a little longer while I get the electricity supply sorted out.

I need to review the “just flip the switch” and use 110V. I didn’t see any of that in the user guide but that doesn’t mean its not in there. I just need to read it again and probably do more googling.

Thanks for reading and Happy Rovering.

March 14, 2023May 16, 2023

Transfer Case Knob Repair (Post #604) 3/14/2023

Looking for the thread specification was pretty easy with a Google search. I stumbled on this thread on Rangerovers.net. “Tex” from Italy states its a M10x1.5. “LanceL” had a novel idea to use a M10 Rivnut.

https://www.rangerovers.net/threads/transfer-case-knob-thread-pitch.345708/

I decided to use a M10x1.5 nyloc nut. I also bought a bolt to go with it which provides a clean threaded path to the nyloc nut. I also used some of my supply of Dr. Crafty Clear Epoxy Resin [Amazon.com]. As you will see in the video. I cleaned out the shift knob. I also carved “channels” in the knob to provide “keys” to keep the resin from someday rotating inside the perfectly cylindrical knob.

I then placed the bolt with the nyloc nut on it down inside the knob. Mixed up my resin and poured it in. It took 72 hours to cure. I let it sit for a full week, due to work, and a living history camping trip I had planned at Ft. Towson [Oklahoma Historical Society].

This project turned out great. It was easy, didn’t require any tools that most Land Rover owners don’t already own. I was genuinely surprised this actually work as I had hoped it would. Now I can turn to the rest of the 3000+ things I need to do to the Big Whit Bus to get her back on the trail.

This project was a 1 on the Difficulty Scale.

Support me on Patreon if you feel moved.

Thanks for visiting and Happy Rovering.