Posts

Posted on

Draining the Fuel Tank on a Range Rover Classic (Post #668) 8/25/2024

In this video, I rid the Big Broken Bus, Mrs. Okierover’s new name for the Range Rover Classic, of the crappy fuel in the gas tank. It was not a terribly difficult job, but it was annoying due to the cheap Chinese pump I bought to do the job.

I tried initially to go through the fill tube. That didn’t produce any results worth mentioning. I then decided I could pull the damn fuel pump assembly AGAIN and that would provide the access I needed. It did.

I got nearly all the gas out. It was about 15 gallons. 15 gallons of bad fuel. I took that fuel and added it to the F-150s gas tank. The F-150 has a 30 gallon tank. So adding 12 gallons of questionable fuel to her probably won’t make any difference. I also treated it with Stabil. It won’t take long to burn it up. I go through 15 gallons a week getting to work.

I added 5 gallons of new fuel to the Range Rover and treated it with Sea Foam Fuel Treatment. The label and the interwebs say this will remove varnish. I’m skeptical. I read a bunch of sites and there were lots of proposed solutions. One even said if you use E85 fuel it would eventually break down the varnish. As a rule, I don’t use ethanol in the Range Rover. I know there are times when you must, but generally I avoid it. Ethanol also doesn’t hold up as well as 100% when stored, or so I am told.

The old girl loved the new gas and purred happily after all the bad gas was pulled through the gas lines. I’ll start her up every week and run her to temperature. Hopefully this will minimize the varnishing. Time will tell.

Like and Subscribe! Comments are always answered. Patreon if you feel so moved.

Posted on

Fuel Pump Failure: Part Duex (Post #667) 8/19/2024

Well here we go again. I decided this weekend I was going to get the Big White Bus started and move her out of the shoppe. I tried to get her started and nothing. I didn’t hear the fuel pump kick on. That’s…a bad sign.

So I asked my son to help me test. I had him turn the ignition on while I checked the voltage at the fuel pump. I had voltage.

That eliminated a LOT of testing of other components. I had a bad feeling the fuel pump was crapped out again. Turns out I was right. It was completely varnished.

What the hell right? I put 5 gallons of fresh gas in it back in December after I replaced the rubber filler hoses. I guess that wasn’t enough fresh gas. I called my friend JagGuy and asked some “chemistry” questions regarding gasoline.

Is it possible that the gas in the tank is so far gone that it varnishes? Its possible was his reply. We came to the same conclusion that all the gas needs to be removed and fresh gas added. We also talked about fuel stabilizer. I’ve never used fuel stabilizer. I guess I’m going to use it going forward.

Who knows how long the Big White Bus is going to be laid up until I can get her running regularly? Not me and I’m the project manager! So fuel stabilizer is going to be all the rage. And I’ll start running her on a regular basis.

What is odd are all these “This [insert vehicle type here] has been sitting in this field for 30 years!!! Will it start?!?!” videos on Youtube. JagGuy surmised, probably accurately that most of the truly ancient stuff has mechanical fuel pumps. Throw in a fresh battery, hope the rats haven’t eaten the wires, and if they drain the tank and use fresh gas…maybe that’s how they get them started.

Otherwise I’m calling bullshit on all these videos. There’s no way 30 year old gas is any good. My gas is five years, old give or take a year, and it’s crap.

Now I’m going to be tasked with trying to drain the tank. And then what do I do with it. Do I dare trying to mix it with good gas and burning it in my cars? What do you think?

If you watch the video you’ll see a demonstration on how simple it is to fix the fuel pump.

Like and subscribe. Patreon contributions are always accepted.

Thanks for reading and Happy Rovering.

Posted on

Footwell Repair Part 7: Floor Panel Repair, Final Assembly (Post #666) 8/12/2024

Post #666!!!! Not today Satan, I finally wrap this fender up. Maybe a proper Devil Dog would have made a more creative 666 post. You’ll just have to settle for one of my old tags.

Mrs. Okierover made me get a new tag…she’s religious that way.

Anyway, I got this beast reassembled. Mostly reassembled…okay I got the fender on and the wiring loom back in place. It’s significant okay!? Dang!

My grand son Grady came over (mostly because he was bored at home) to help. And help he did! A lot of what I filmed before he got there was lost. I truly hate this GoPro, if its not overheating halfway through a shot, it’s dropping files, or losing the sound track off a segment. Trash. I’ve read a bunch of complaints about this GoPro 11. Several telling everyone they’ve fixed a bunch of the overheating in the GoPro12!! Now it overheats 1/3 less! Nope. Not gonna fall for it. GoPro, if you want to redeem yourself you can send me a 12 for free and I’ll give it a review. You probably won’t like the review, but I’ll give one an honest one.

Back to the assembly, I got the wiring loom put back in place. It went surprisingly well. The fender went on pretty easy. I did make one mistake in the building of the side bulkhead. I should have made it longer. The result was I didn’t have one of the two fender mounting places. I also lost some hardware. So I went to the hardware store to get replacements. Met a fellow Marine building a Skoolie camper for his family to travel in. Sounded like a fun project.

When I got back and Grady and I had wrapped up the video I was finishing the assembly and guess what I found?? Yeah, the missing screws and bolts I stopped looking for 3 hours earlier. Isn’t that just typical.

On an annoying note… the damn Big Whit Bus wouldn’t start. So I get to deal with that issue again. YAY! /sarcasm font.

Like and subscribe! Or whatever.

Thanks for reading and Happy Rovering.

Posted on

Footwell Repair Part 6: Floor Panel Repair, Seam Sealer (Post #665) 8/5/2024

I started the weekend fixing my 2014 F150. I’ve been hearing noises from the front and could feel some vibration in the floorboard. I talked to a few of my co-workers and they diagnosed wheel hubs. So I ordered a set of Timkin hubs and new brake discs and pads. I spent 5 hours putting them on. I setup the awning for shade so I wasn’t in the sun the whole day.

Victory was mine and I spent the rest of the day mowing the yard and working in my pumpkin patch. I have 5 Kakai pumpkins so far and will have a bunch of pepitas to munch on.

Sunday I set to getting the seam on the new panel sealed. Nothing too exciting about this. I did learn that 3M seam sealer is way more expensive than the German made UPOL brand. 3M $72.00(US), UPOL $22.00(US). That’s a big discrepancy.

I’ve got a problem with the welds on the transmission tunnel side. I can’t reach them to get them cleaned (the panel under there is oily and dirty), the rubber coating (no longer attached to the steel), and I can’t get to the panel because the exhaust is in the way. I’ll need to drop the exhaust. I’m not excited about that. I need to get her up on a lift to see if it would be easier. More on this on another post.

I’ve got everything sealed. Next up, I need to coat all the panels in the wheel well in truck bed liner. I’m hoping this will DELAY the inevitable.

The next post will be me fumbling to remember how to reassemble this part of the truck.

A little shout out to Mrs. Okierover as it is our 35th wedding anniversary this weekend. Happy Anniversary sweetheart.

That’s about it, like and subscribe, and as always Happy Rovering.

https://youtu.be/yBh2xRWomw0
Posted on

Footwell Repair Part 5: Floor Panel Repair, Panel Finally Installed (Post #664) 7/27/2024

Yes! I finally have the panel welded in. Is it pretty, oh hell no. Is it water tight, not even close.

I will liberally apply seam sealer. You’ll see that in my next video. I had a helluva time getting that panel held in place. I finally came up with a solution. Use a 50lb bag of sand to hold it in place while I set some welds. This could not have worked better.

I was also able to hammer the panel grooves flat. I went and got my grandson “Thumbtack” and had him hold a 10lb weight against the panel while I hammered on the opposite side. This work pretty well I guess? I don’t know. If I was better at body work I would have built a jig and made a panel with the same grooves. But I’m not a good body worker.

I covered as much of the panel in primer as I could reach. What I learned when I crawled underneath to spray primer on the panel was a big bummer. I found the welds had heated the rubber covering on the transmission tunnel. This caused the rubber to separate from the panel and you can guess what’s going to happen under there.

No, that was a terrible guess….really? It’s going to rust, rust a lot. I haven’t a clue what I’m going to have to do to get to this area and get it covered with paint and rust preventative coverings.

As I’ve said it a dozen times, every job creates two more jobs.

I have a shout out to Tumbleweed Garage [Youtube]. He’s working on a 1948 Willy’s Truck. I enjoy his work.

Thanks for reading, like and subscribe, and Happy Rovering.

Posted on

Footwell Repair Part 4: Floor Panel Repair, Failing Spectacularly at Metal Working (Post #663) 7/20/2024

I started the day with glorious visions of finishing the welding on the Floor Panel. All I managed to accomplish was spectacular failure.

Things that worked:

  • I had some luck with my homemade plug weld drill bit. It worked well at removing the layers of primer and seam sealer I had foolishly laid down.
  • Welding. Some of my welds actually held pretty well. I managed to get a good ground and the welds stuck until I stressed them too far. On second thought, maybe that means the welds sucked.
  • My home made air hammer … hammer bit stretched the metal a lot. But the shape I needed and the one the I got weren’t going to work.

Things that didn’t work:

  • Welds. As before, they popped when put under a lot of stress.
  • My understanding of metal working,
  • My spinal cord did not like the constant bending over.

After I had the panel welded in place I tried to apply my air hammer on the panel to get the metal to stick. I also tried using self tapping screws to get the panel to stay in place. This may have worked better if I had shaped the panel better.

All in all, it was a waste of wire and gas. I’ve since cut the panel down smaller. I cut all the plug welds off. I’ll try edge welding when I start return to make the fix. Changed the way the transmission tunnel weld was fixed. It’s now straighter less “bowl shaped”. I’m pretty sure I’ll need help holding the panel in place while I make the first few welds.

Range Rover 1

Okierover 0

That’s it for this week. Like and subscribe.

Thanks for reading and Happy Rovering.

https://youtu.be/-0hDDW1aPcE
Proudly powered by WordPress