Installing the Upper Dash on my Range Rover Classic Overland Rig (Post #702) 5/5/2025

Things are starting to come together.

In this video I am finally starting to get the trim back into the Range Rover Classic. I had to do some touch up to some of the pieces. I got that all done.

I also forgot the steering column cowling. So I got that off and gave it a coat of paint and at least three coats of matte clear. This is in the sun most of the time and frankly I’m surprised it isn’t in worse condition.

The rear wiper switch on in the cowl didn’t want to come out. The tabs were badly bent. I don’t remember ever touching that so I can’t say it was me that damaged it. In any event, I had to take it apart to get it out of the cowling piece. And as you can probably follow, I had to refurbish it a bit to get it reinstalled.

I also popped one of the bullet connector ends of the wiring off and had to repair that. That too a little quick thinking as they are very small and the crip was really going to be a bitch to solder. So I used a small jewelers screwdriver end and tapped it through the connector to open up the prongs. This worked better than I thought it would. So bully for me!

I had to make a run to the hardware store for “hardware” to replace the bolts on the passenger side. I found four nuts in my stash for the instrument panel. Where I put all the hardware to take this dash apart is still a mystery. I’ve dug through all the project cups and pie plates and have not found one that had the correct parts.

So I guess I’ll just keep replacing the “hardware” with new. And then one day, I’ll find all the original hardware and think to myself, “why did you put it in that spot?”

Thanks for reading and Happy Rovering.

https://youtu.be/qFQNVr_0WD8

I Installed the Seats on my Range Rover Classic Overland Rig (Post #700) 4/27/2025

POST SEVEN HUNDRED??????!!!!!!!!!

How is that possible? I’d like to thank you for reading. If I didn’t think this page helped anyone, I wouldn’t do it….for free….well it actually costs me to provide it. But its giving back, and if it helps you, it’s worth it.

Well the seats are back in! I don’t know how to describe how awesome it was sitting in the the Range Rover Classic, on my seats. In the video I say, these are the seats I was meant to sit in. I really mean that. I LOVE SITTING IN MY RANGE ROVER.

I also did some cleanup under the seats. There was a lot of…dirtiness? Not sure how to describe it. A lot of it was metal dust from grinding. Some of it was just years of french fries slipping between the seat and transmission tunnel. Just kidding there were no french fries under the seats (this time).

I got some Dawn dish soap, a little bleach, and hot water. It did a fair job getting the muck off. I feel better about it, so that’ll have to do.

Thanks for reading and Happy Rovering.

Too Cold to Paint, Planning What’s Next on my Range Rover Classic Overland Rig (Post #698) 4/7/2025

Third Winter hit this weekend.

It was too cold to paint. Temps in the forties in my shop. I didn’t feel like getting bundled up to lay on my back getting paint all over me.

Call me lazy, that’s fine, but not super fun for me. So I’m going to tackle the sealing of the seams with paint, seam sealer, and truck bed liner next weekend. I’ll get it as “protected” as I can.

In this video I also talk about what is coming next. Call it a little planning. I have a lot of wiring to run. Lights for the interior and exterior and wiring for a battery management system. I need to plan for a DC to DC converter and all the magic electronics that make everything work well together.

I also allude to some fun history in the story of Tuck’s Ferry across the Red River (RedRiverHistorian.com).

I also mention some of my current storage solution in the U.S. G.I. Aluminum Medical Transport Chests. If you’ve followed for any time, you’ve seen me talk about the.

This is going to be a lot of coin to drop. So getting the wires run will require some planning. I’m certain I’ll screw this up and have to re-run some of this. But that’s part of the fun, right?

Thanks for reading and Happy Rovering.

Welding Completed on the Floor Panel on my Range Rover Classic Overland Rig (Post #696) 3/23/2025

In this episode, I manage to get some good welds. Together with some bolts, I think the floor bed is installed!!!!!

Now I need to clean up the welds and cover the steel in some primer and paint. You know, to prevent rust, wink, wink.

I know this will rust again, I’m just hoping by the time it does, I’m on to another vehicle.

Thanks for reading and Happy Rovering.

https://youtu.be/uMbmCFAEUi8

Hotter Welds for the Floor Panel on my Range Rover Classic Overland Rig (Post #695) 3/16/2025

Yeah, these welds go to SEVEN. As Nigel Tufnel of the legendary band, Spinal Tap, says, “…but these go to eleven.” I turned up the voltage on my welder to get better welds.

I started with setting 4 wire speed and C voltage on my Lincoln Pro Mig 180 welder. Those welds did not hold. Drilling them out ate two drill bits and caused me to sharpen one of them twice during this ordeal.

So I turned it up to 7 D. Why the wire speed needed to be so much faster at this level of voltage is till a mystery to me, but hey, whatever works.

Hopefully these work. I am going to reinforce the welding with some bolts just to make sure any “flexing” of the body doesn’t sound like I just cracked the Big White Bus in half, when those weld break free. It will give me some piece of mind too that the floor bed will not go anywhere with all my gear strapped to it.

I also sorted out that I had my braces on wrong. This was why the bed was bulging in the middle. I don’t know how many times I went through how those needed to be installed and I still got them wrong. They are on correctly now and the bed panel fits SO much better.

That’s about all. I really appreciate two of my viewers who pointed out that the welds were not penetrating.

Wallace, who just recently acquired a Range Rover Classic and will be starting on his restoration at some point in 2025. And…

Trevor from Tumbleweed Garage [YouTube channel] who is restoring a Willys Pickup. He is doing a great job and I love watching how his mind works. He does a lot without any fancy tools, proving once again you don’t need to spend a king’s ransom to play with cars in your garage.

Thanks for reading and Happy Rovering.

https://youtu.be/17mumd38By8

Fitting the Floor Pan on my Range Rover Classic (Post #692) 2/23/2025

In this post I fit my floor panel in the Range Rover. Yes, I know, it’s about time!

I finished up bolting on the support beams and got the panel test fitted in the Big White Bus. This required me to go to the hardware store and buy a bunch of stainless steel hardware. Fortunately for me I bought a box of 100 bolts. Unfortunately for me the bolts had a 37.5% failure rate when fastening them with nyloc nuts.

Why? I have no idea. It’s not like I was torquing the hell out of them. I hadn’t even bottomed the nuts out and the bolts were binding up. Pretty disappointing. I’ll be sourcing a different brand of hardware in the future. These really let me down. I’ve had problems before but thought it was me being rambunctious with the impact driver. Turns out it wasn’t that after all. You might be quick to say “made in China” I’m not surprised. But these were made in Taiwan. Normally an acceptable substitute, and if that helps them stick it to the CCP I’m all for it. Not sure where I’ll find another brand but I’ll be looking.

The panel fit was “tight” to say the least. It required a bit of persuasion (with a hammer) but it fits. The next step is to get the damn thing welded into place. I probably have 100+ plug welds to do. This is going to be a challenge.

I can see the end of this part of the project in sight so I’m excited to get after it. That’s all for this week. Like and subscribe if you enjoy the content and appreciate all the free content.

Thanks for reading and Happy Rovering.

https://youtu.be/2Svh-SdwGOE