Footwell Repair Part 11: Wheel Well Panel (Post #658) 6/19/2024

In this post I talk about making my replacement panel for the front passenger side wheel well. I went to Chickasha Industrial and bought a piece of scrap 20 gauge. It will be just the right amount for the fender and the floor panel. Happy I didn’t have to buy a giant sheet.

I started by making my measurements and then checking them again. After I finished that I checked the measurements again. In the video I show how I needed to have a trapezoid shape. And after typing trapezoid in this post I realize I have spelled it wrong in this post, which is being exported as I type up this post. Oh well…..

I referenced “Mephisto’s Trapezoid” from the 1981 Pee Wee Herman – Live at the Roxy show which was on HBO. It’s one of my favorite shows to watch and was the inspiration for Pee Wee’s Playhouse. Captain Carl, played by the amazing Phil Hartman, tells his story to Pee Wee about getting lost in Mephisto’s Trapezoid. Comedic genius.

I cut the steel and then measured again. I made some bends to get the inner edge and the back lip right. After getting the panel made I could tell I needed to make some adjustments to the fender well too. So I did some hammer and dolly work and got everything sorted. I also had to adjust my panel after I got everything sorted. No biggy.

I dry fitted the panel at least six times. I’m pretty sure I can get it into place with just a few plug welds. I’m going to try my hand tomorrow at modifying a broken drill bit to make a plug weld bit. If that doesn’t produce results I’ll probably run to a welding shop and see what I can find. The gist of this is you can paint everything and seal it with whatever then remove just the part of the paint you need to weld.

This is a giant experiment because the entire floor pan in the back is going to be done this way. The holes are there and all I’ll need to do is get the Z bar in place and make a crap ton of plug welds. Then I can get the entire seam sealed with bedliner and or whatever.

That’s pretty much it for now.

Like and subscribe and Happy Rovering.

https://youtu.be/nPFNPa3TgQY

Footwell Repair Part 10: Fender Prep (Post #657) 6/10/2024

In this post I intended to patch the fender with a new panel. I only have a smallĀ  section of the steel sheet I bought. Before the work I started today I needed a 10″x8″ piece. My patch area was about 7 inches with a 9 and a half panel with a half inch bend on one side.

From last week we found 4 sheets of steel sandwiched on the one side. Two of those are seemingly superfluous. In between each sheet was a nice rust stuffing. So its pretty obvious all that needs to be remediated.

I got the air chisel out and went to town. I split all the steel and cut away the rusted parts. I wire wheeled as much of the rust away and in the end covered everything with the rust mitigation paint I bought.

I will need to get a new sheet of steel to finish this piece. The patch I need to make is now going to need to be a inch after the bend perhaps more. I’ll cover every piece of steel with the rust paint. I think the way they screwed the panels together might work. I can also see how I could spot weld the panels together. This would also be good experience for welding the bed back into place. I will also be covering everything in seal sealer and several liberal applications of bedliner/rhino-liner or whatever it is called.

Thanks for watching, like and subscribe, and Happy Rovering.

Footwell Repair Part 7: Building an “L” for the Bulkhead (Post #654) 5/19/2024

Part 7 should have been titled, “How the hell are we going to make an L that has a big bend in it?!?” I have been thinking about this solution for two weeks on and off in my spare brain idling time.

Today’s video is me actually experimenting with bending the metal and making a sample piece. I’m pretty sure I know what I’m going to and how I’m going to put this thing together. The next step is to cut the strip I’m going to use for the L piece and hammer it into shape. I’ll need to do some additional measuring and mental gymnastics to sort out how I’m going to weld all this up so it doesn’t leak and dare I say it, “it doesn’t rust” or “rust much”.

1820’s Cherokee

I also mention that I went to the 200th Anniversary of Fort Towson. You can google about Fort Towson that was once known as the Chateau on the Prairie. It must have been a wonderful sight to behold with it’s limestone walled buildings and it’s blue roofs.

Life on the prairie in this time was hard. Like real hard. Death was ever present and it was not uncommon for a soldier to arrive and be dead within a year. They grew much of their own food and getting supplies from the east was inconsistent.

As a living historian, I portray a Cherokee for this period in Oklahoma history. This was the time when the creator of the Cherokee syllabary Sequoyah lived. The fur trade in “Indian Territory” pre-dates the mountain man era of the fur trade popularized in several movies like Jeremiah Johnson (1972) and The Mountain Men (1980).

As always like and subscribe to the blog and Youtube channel.

Next week will be more metal bending and welding of the support into place to get ready for putting in the floor.

Footwell Repair Part 3: Investi-Disassembly (Post #651) 4/12/2024

thumbnail Footwell Part 3

UGGGGGH!!!!!!
Will this ever end?

I think I know the answer to that. But I have to show my exasperation. This rust find is possibly the worst thing ever. It’s in the most terrible of locations.

Mrs. Okierover said, “Maybe you should call it Rusty Rover instead of Okierover.”
She’s not wrong.

Every where there’s red its rusted through.

It’s as bad as you can imagine. There are at least four different panels converge in this area to form the firewall, fender well, and the foot well.

There are a LOT of peripherals that run through there too. Including the fuel lines which I may have nicked when I was air chiseling the panels out. If you’ve followed the blog for very long (at least since 2010) you’ve seen The Evil German Dude and I attempt to fix the floor pan when it rusted out.

We had fun, but we failed to keep the water out and our work finally failed. I had an ongoing issue with water getting in and wetting the fargin’ OPEN CELL floor pads under the carpets. The carpets too we constantly wet. I found the place where water was getting in making the carpet wet. It was through the firewall at the corner where it married up to the side wall.

As you will see in the video, this rust is bad. Real bad. The repair is going to be really difficult and probably beyond my skill set. That being said, I have to fix it myself. There is no money to send it off. The body work itself would likely cost more than the entire vehicle is worth.

I’ve still got a LOT of work to do. I need to find a solution. It will probably be welding several panels together. I’ll need to study it more to make my mind up.

I stared at it at least an hour while I shot the video. Still struggled to sort out a concrete idea.

I am going back out the weekend this is published as OkieF150. We are going to the 200th Celebration of Fort Gibson. Fort Gibson is the oldest town in Oklahoma. Way back when it was still Indian Territory the United States needed a fort to protect the trade from this area.

We are going to make a weekend out of it and I’m hoping we can get some fishing in while we are at it. This will be the last overlanding trip for this year as I will be spending every weekend for the rest of the year trying to sort out all these issues.

Like and subscribe on the videos and the blog.

Thanks for reading, and Happy Rovering.

Footwell Repair Part 2: Disassembly (Post #649) 3/24/2024

Thumbnail Footwell Repair Part 2

In this installment I begin the disassembly of the front fender to expose more rust. And I was NOT disappointed. I found just about what I expected. A rusted through footwell. On a positive note…I think I found where the water was getting in to soak my carpets. I have no idea how to correct it, but at least I found it.

In order to get to all the rust the front fender had to come off. I encountered a bunch of rusted screws and bolts. I had to cut several of them off. I even used an air chisel to remove some spring type U nuts (yeah I had to look that name up, I had no idea what they were called). I can tell you they were a bitch to remove. But after you deconstruct them a bit they came right off. I’ll likely replace the U nuts with stainless steel bolts and nuts.

The fender didn’t put up much resistance after I got the U nuts off. I then had to remove a plastic fender piece. You can probably guess that the plastic clips weren’t going to survive being taken off.

Underneath I found a lot of surface rust. I put the angle grinder with a wire wheel to work. I cleaned up some of the rust and found a bunch of really bad metal.

In the seem between the wheel well and the footwell I found what I think is the source of my wet carpets. This spot is going to be hard to fix. I don’t know what needs to be cut away and what needs to be welded on.

Inside where this failed bulkhead is is covered with Fat Mat. That will need to be removed. Heat gun and patience I hope will assist me in getting it removed. There is a nice cluster of wires and relays right there too. So joy of joys I’ll get to relocated all that too!!! Woot!

I also took the lug nuts and cleaned all the rust off them. I have the first coat of paint on them. They’ll get a second before I put them back on.

That’s about it for this week. I got to watch some severe weather out in western Oklahoma on Sunday. It all petered out before it got to the Okierover Base Camp.

Like and subscribe the video.

Never trust quotes in social media.

https://youtu.be/Hr4vN39uf8c

Footwell Repair Part 1 (Post #648) 3/17/2024

Thumbnail Footwell Part 1

“Just When I Thought I Was Out, They Pull Me Back In!”

– Michael Corleone (Al Pacino) in Godfather: Part 3 (1990)

That’s how I feel every time I find a new rust patch that is going to require a major repair. I have already repaired the passenger side footwell. You can check that post out here…

Good times….

Investigating the rusted panel has revealed the patch rusted out. This is going to be a complicated repair this time. This time, I have to figure out how to connect the new panel to the side wall of the footwell.

I’m not sure I have the tools or the talent frankly to bend the steel and to shape one side at a 90 degree angle. Sorta like this image but with more curve in the panel.

Or that’s what my pea-sized caveman brain thinks I need. I haven’t found any videos on line demonstrating how to do this complicated piece. Even Church House Classics [YouTube] didn’t have it in his latest video. I’ve got a couple of ideas how this is going to go. None of those ideas seem easy at this point. They make a replacement footwell but there are none in America. It’s a $60.00(US) part that costs $86.00(US) to ship.

Once I get all the rust removed this project may reveal itself. At least that’s what I’m telling myself. Once I complete this I have to up to the front wheel well and get the surface rust under control. It never stops, and I keep getting pulled back in!

Like and subscribe to my YouTube channel.

Thanks for visiting and Happy Rovering.

http://patreon.com/okierover

Footwell Repair

https://youtu.be/knlOFCR9sEU