Floor Support Beams on my Range Rover Classic (Post #691) 2/17/2025

In this post I pose a question, “Why not bolt those supports on?!?”

I have the holes for bolts. I either have to weld those holes up or use them to mount the supports. It’s only a few bolts to get the beams attached. Bolted or welded I have the same result.

So I decided to bolt them on. I went through my stash of stainless bolts. You KNOW those bolts would have to stainless as do the nyloc nuts and the fender washers. So I needed a run to the hardware store. I had a coupon for 20% off on $50(US) so…let’s go nuts…I mean nuts and bolts.

I am now ready to mount those beams. I managed to get the shop up to 57 degrees Fahrenheit so I sprayed some primer on the bare metal. I then decided I needed to move the beams and the floor pan into the sunroom in the house. It is climate controlled and the paint will cure more effectively if the temp is above 60F.

I also sprayed bedliner on the floor pan too. This rubberized material will help form a water tight water resistant mount once I get this all bolted up. I’m feeling pretty pump about it actually.

The next episode will have the beams installed and mounted in the Range Rover to assure the fit is right and then to weld the pan in place.

Thanks for reading and Happy Rovering. Like and subscribe. I really appreciate it.

https://youtu.be/8bUl7TqlNJk

Welding up the Floor Supports on my Range Rover Classic (Post #690) 2/9/2025

In this update I begin attaching the supports to the floor pan. Also in this update I tried to get carbon monoxide poison and avoided getting bit by a fiddleback spider.

I started on the supports and the first one was the strap across the back portion of the floor bed. When I removed the strap during my tear down I drilled out the welds. I did a decent job and only punched through on one weld. This allowed me to plug weld the strap back into place.

This was fortuitous. The other support beams are drilled through. That’s gonna make reattaching …difficult.

Since it was a bit chilly in the shoppe, I fired up the kerosene heater. I done this several times in the past. Before I closed the overhead door a little exhaust from the Big White Bus managed to get in. The heater must have added to a substantial amount of carbon monoxide. This set off the sensor. So I opened up the door to let the monoxides out.

I also moved the alarm, under the alarm was a damn fiddleback spider. The cold didn’t allow for the damn thing to scurry away. I ended it right there with a tap. When it twitched, I gave it a SMASH. One less brown recluse spider is a good thing.

I now have one of the three supports into place. The other two will not be as fun.

Like and subscribe if you are enjoying the content. It is appreciated.

Thanks for reading and Happy Rovering.

https://youtu.be/n2oFRhvDRRs

Does the Repaired Floor Pan Fit on my Range Rover Classic (Post #688) 1/19/2025

In this video, Part 4 of 12? (I’ve stopped counting), I dry fit the repaired floor pan and contemplate how I’m going to get the braces welded up.

Well…it fits. It’s not great, but I think it will work. There are going to be gaps and those will need some seam sealer to make them water-tight.

The holes in the panel will present a welding challenge. The holes will likely need to be filled prior to welding on either the brace or the panel. I’m not sure which will be the best.

So there are some decisions need and I’ll have to fix it to get this project completed.

As always I appreciate your patronage. Like and subscribe.

Thanks for reading and Happy Rovering.

https://youtu.be/99KY8okKVuo

Patching and Painting the Floor Pan on my Range Rover Classic (Post #687) 1/12/2025

In this week’s post I continue my work on the floor pan. This time it’s patching the panel wear rust munched it’s way through. I patched a roughly 4″ x 5″ piece and three holes. One was about the size of a quarter the other about the size of a nickel.

I made up a template cut it out for the 4×5 hole. For the smaller holes I drilled them out to make them uniformly round. This helped greatly with making the patches. The third hole I just welded shut by building up the weld to bridge the hole.

I had a bit of trouble getting the welder dialed in. I haven’t changed the setting but for some reason it the welder was being difficult. Once dialed in (set back to the original settings) I managed to get good penetrating welds.

Once it was all patched up I got some paint on every thing. I was also able to get some rattle-can rhino-liner/stone chip sealer on the Z bar. I still believe this is crucial to keeping the rust at bay for a few more years. I will likely put a bunch of seal sealer in there as well. Belt and suspenders if you know what I mean.

My next episode will be getting the cross beams installed. This will be a challenge I can assure you.

Thanks for reading and Happy Rovering.

https://youtu.be/uoWbYqQfFh0

Floor Pan Repair on a Range Rover Classic: Part 2 (Post #681) 12/2/2024

I hope everyone had a wonderful Thanksgiving.

I am back working on the floor bed in this episode. The bottom half of the bed had not had the surface rust ground down. So I turned to and got some grinding done.

I used the wire wheel to get started. There is some use of factory seam sealer. I can’t imagine what the factory was thinking. There is nothing to “seal” on the underside of the truck in the places this was used. Now that I am adding new sides…there is definitely some seams to seal.

Everything will be covered in paint. When the welds get applied there will be some gaps between the new Z bar and the old bed. I’m thinking seam sealer will be helpful to keep water out. I’m also thinking of some sort of wax I could heat up and pour in the gap. I’ll do some additional research but this has possibilities.

I get all the rust off. I also used the sanding disk on some of the more pitted rust. That seemed to work pretty good. These sanding disks are expensive in my opinion. They still might be worth it but I’m not sure.

That’s about it for this week. Next week I’ll be fitting the Z bar and making sure everything will fit in the gaps.

Like and subscribe.

Thanks for reading and Happy Rovering.

Floor Pan Repair on a Range Rover Classic (Post #676) 10/20/2024

In this installment I start getting the rust sorted out for the installation of the floor pan. The cross members have quite a lot of rust on them. I used the wire wheel, a flappy sandpaper disk, and even a cutting disk to remove the rust.

The removal went pretty well. It took a few hours. The lip of the floor where the panel was cut out required wire wheel work as well. This was just a LOT of grinding.

I decided to setup and use my sandblasting cabinet. With the new air compressor it worked great. I was really pleased with the result. So much so that I’ll be building a rolling base for it. That way I can store it when I’m not using it and pull it out to make it more convenient. The lamp inside the cabinet has seen better days so I bought a cheap under cabinet lamp that I will install.

At the beginning of the video I briefly reinforce that I still have a parasitic draw. I’m going to experiment with some solution. One, isolating the alternator. I’m still fairly convinced that the alternator’s diode pack has failed. It’s happened before.

Second, I’m going to test for the draw using the “Pull One Fuse While Watching an Amp Meter” method. It takes forever (30 minutes) but should show what’s going on.

There will be a whole video for that.

Thanks for reading, like and subscribe, and as always Happy Rovering.