Floor Pan Repair on a Range Rover Classic: Fitting the bed Part 1 (Post #682) 12/10/2024

In this post my grandson and I work on the floor bed to get it to dry fit. The first thing we needed to do was to get the Z bar into place. This required us making the side rail straightened and in some places cut some useless steel off.

The next thing we needed was to tack weld the Z bar into place. This was quite the challenge. I tried tacking and it didn’t take. I finally got my weld to hold. I let Grady weld too. His welds would not stick either.

After some frustration we determined that likely we didn’t have a good ground. I put in a lot of effort to get this steel painted so it wouldn’t rust. That unfortunately also prevented us from having a good ground for our welding.

I ground off a lot of paint. This is going to be a problem. The whole reason for the paint is to prevent the damn rust in the first place. So once I get the Z bar in place I’m going to need to paint everything again.

We finally got the Z bar into place and tried to fit the panel. We are about an 1/8 to a 1/4 of an inch off. This is going to require some additional cutting and more fitting to make sure we have it right before we start attaching the braces.

This is part 1 of 2. We spent WAY too much time with welding and prepping. So I cut this down to under 30 minutes.

Like and subcribe.

Thanks for reading and Happy Rovering.

Floor Pan Repair on a Range Rover Classic: Part 2 (Post #681) 12/2/2024

I hope everyone had a wonderful Thanksgiving.

I am back working on the floor bed in this episode. The bottom half of the bed had not had the surface rust ground down. So I turned to and got some grinding done.

I used the wire wheel to get started. There is some use of factory seam sealer. I can’t imagine what the factory was thinking. There is nothing to “seal” on the underside of the truck in the places this was used. Now that I am adding new sides…there is definitely some seams to seal.

Everything will be covered in paint. When the welds get applied there will be some gaps between the new Z bar and the old bed. I’m thinking seam sealer will be helpful to keep water out. I’m also thinking of some sort of wax I could heat up and pour in the gap. I’ll do some additional research but this has possibilities.

I get all the rust off. I also used the sanding disk on some of the more pitted rust. That seemed to work pretty good. These sanding disks are expensive in my opinion. They still might be worth it but I’m not sure.

That’s about it for this week. Next week I’ll be fitting the Z bar and making sure everything will fit in the gaps.

Like and subscribe.

Thanks for reading and Happy Rovering.

Diagnosing Parasitic Draw on a Range Rover Classic: Part 2 (Post #679) 11/18/2024

The Grounding.

Let the grounding begin!

When adversity strikes, that’s when you have to be the most calm. Take a step back, stay strong, stay grounded and press on. – LL Cool J

Authority is supposedly grounded in wisdom, but I could see from a very early age that authority was only a system of control. – Joe Strummer, The Clash

I’m quite grounded. – Enrique Iglesias

Like Enrique…the Big White Bus is now very well grounded. In this installment I install the grounding cables from the battery to the body and the frame. Very important things to have grounded.

The driver’s side is well grounded too. Those ground points to support the ignition system and the engine being grounded to the body. They are lovely.

The passenger side, I couldn’t say that before I finished this job. The ground points probably had not been removed and freshened up since it was wrecked by the previous owner some time in 2000.

The job was not difficult. I got side tracked with a bunch of rust and that removal made this video creep over the coveted 24 minute mark. I actually don’t know what the best length of video is. If you have a sweet spot, comment and let me know.

Three points in this job were the control module for the electric fans. The body which you connect to the fender. And finally the frame connection just behind the recovery points on the front of the frame.

All it took was a little wire wheeling with the Dremel. Cleaning he frame connector. I used a little dielectric grease between the metals. I have no fantasy that this grease will still be there even a year from now.

I found some rust and I knocked that out with some wire wheeling and applying the rust encapsulating paint. Maybe if the painting gods smile that will help keep the rust away.

That’s about it for this week. Like and subscribe and I look forward to your feedback.

Thanks for readying and Happy Rovering.



Diagnosing Parasitic Draw on a Range Rover Classic: Part 1 (Post #678) 11/10/2024

Parasitic draw. Nothing is worse than electric problems with your vehicle. Nothing. Nope…not even that….or that. Electronic problems top the list. Okay, I googled it and electric problems weren’t even on the list on some sites. It’s numero uno on my list so let’s run with that.

In this installment I set out to the source of my parasitic draw. Seems like this is a common issue with older cars and British cars in particular. This is not the first time for me. A few episodes ago I diagnosed a possible failed alternator. When the diode pack fails in an alternator it can lead to dead batteries.

I currently have the alternator isolated so I know my issue isn’t that. I setup the multimeter in series with my battery and got it placed on the windshield so I could watch the setting change.

I started with 1.9 amps of draw. I pulled every fuse in the fuse block to no avail. I then started on the auxiliary fuses under the passenger seat. There is a row of covered fuses, I check all those. There is also two fuses stuck on the side. Turns out one of these was the culprit. When I pulled the red 10 amp fuse the draw dropped to .01 amps.

I have 4 manuals and one of them had the fuses identified. This fuse was the fuel pump. Now that’s a bit of a puzzler. The fuel pump is OFF when the key is off. I spent a lot of time thinking about it. And I didn’t come up with anything. I’ll need to look at the electrical circuit and see what comes up. I’m also going to call JagGuy and get his take on it.

This is part 1 of I’m not sure how many parts. As many as it takes…

This weekend was the Marine Corps’ 249th birthday. I give a shout out to my friends and family who were Marines. I also gave a shout out to all the veterans in my family. There were a bunch.

Marines, my grandfather William Alvy Stephens served during the Banana Wars after WW1 and my uncle Ben Johnson on my mom’s side served during Vietnam. I also served with several friends who also served with me in the USMCR and went on to retire, MGySgt Jason Rogers, USMCR (ret.) and Col. Mike Gann, USMC (ret.). My friend Howard McKinnis also served in the Marine Corps during Vietnam. My wife has several cousins who also served and retired from our beloved Corps.

I come from a long line of veterans. Both my dad and uncle served in the Navy. Another uncle on my mom’s side served in the Navy. My cousin Victoria retired from the Army and she had a son who also served in the Army. My cousin Dan served in the Air Force and a son of his served in the Navy. Many of my Great Uncles served during WW2 in the Merchant Marines and in the US Army Air Corps. Brave men one and all. I’m sure I could go on to name all my cousins who are married to military men but I’ll stop here.

Thank you for your service to our great nation.

Like and subscribe, thanks for reading and Happy Rovering.

Diagnosing a Bad Battery on a Range Rover Classic (Post #677) 11/4/2024

A thumbnail.

Yep, you read that right…bad battery. Two weeks ago that battery was fine. It held a charge…or seemed to. But this weekend it decided to cross over to the big battery charger in the sky. The only thing different this week from previous weeks, was I left the battery connected.

I had removed the alternator from the system by pulling the charge cable. So only the rest of the vehicle would be the only thing parasitically draining it. I didn’t think I’d have to work 32 hours out of 48 that 1st weekend, so the experiment was a little skewed.

So when I put the meter on it and it registered 0.00 volts, I was a bit bummed. I they decided I’d try to charge it with trickle charger. I hooked it up and the needle pegged to full. The alligator clips started getting hot. My thought, “That’s not right.”

It wasn’t right. I hauled the battery down to O’Reilly’s and had them test it on their fancy tester. (I need to buy one of these, hmmm….eBay?) It said the terminals were not connected. We guessed a dead cell was shorting it across the terminals. Not sure about that, but they weren’t connected.

So $242.00(US) later…when did batteries start being so expensive? Damn it seems like the last battery I bought for the Big White Bus was like 60 bucks.

So I dropped the battery in and test fired the engine. She fired up no issue.

I also ordered a new negative terminal. The off the shelf ones just suck. I’m going to try the same style my F-150 has. They work pretty well. The only thing left is to put terminals on the three ground cables. I’ll figure that out this weekend.

So next week I’ll test for the vampiric parasitic draw. Check back next week for hopefully some results.

Like and subscribe, donate if you can, Patreon.

Thanks for reading and Happy Rovering.

Floor Pan Repair on a Range Rover Classic (Post #676) 10/20/2024

In this installment I start getting the rust sorted out for the installation of the floor pan. The cross members have quite a lot of rust on them. I used the wire wheel, a flappy sandpaper disk, and even a cutting disk to remove the rust.

The removal went pretty well. It took a few hours. The lip of the floor where the panel was cut out required wire wheel work as well. This was just a LOT of grinding.

I decided to setup and use my sandblasting cabinet. With the new air compressor it worked great. I was really pleased with the result. So much so that I’ll be building a rolling base for it. That way I can store it when I’m not using it and pull it out to make it more convenient. The lamp inside the cabinet has seen better days so I bought a cheap under cabinet lamp that I will install.

At the beginning of the video I briefly reinforce that I still have a parasitic draw. I’m going to experiment with some solution. One, isolating the alternator. I’m still fairly convinced that the alternator’s diode pack has failed. It’s happened before.

Second, I’m going to test for the draw using the “Pull One Fuse While Watching an Amp Meter” method. It takes forever (30 minutes) but should show what’s going on.

There will be a whole video for that.

Thanks for reading, like and subscribe, and as always Happy Rovering.