Floor Pan Repair on a Range Rover Classic: Fitting the bed Part 2 (Post #683) 12/16/2024

This week is part two of Grady and I trying to get the damn Z bar attached to the bed. We had a helluva time getting our welds to stick. In the end it came down to me removing a lot of the primer and paint I spent so much time getting into place.

The welds were not taking because the ground was poor. It required me to grind off a lot of paint and to get new vice clamps to hold the steel together.

Taking that paint off was no challenge for the power tools. It was painful to me because my ultimate goal in all this was to put this floor bed back together BETTER than it was before. The better is that I don’t have to worry about it rusting out.

Once I get it back together, I am going to spend significant time getting it recoated with paint and rust preventative coverings. This may be challenging with winter now upon us. It was 70F today but it is in the thirties in the mornings. I’m hoping for a warm spell around the new year so I can get the paint applied.

That’s about it for this episode. Like and Subscribe.

Thanks for reading and Happy Rovering.

Floor Pan Repair on a Range Rover Classic: Fitting the bed Part 1 (Post #682) 12/10/2024

In this post my grandson and I work on the floor bed to get it to dry fit. The first thing we needed to do was to get the Z bar into place. This required us making the side rail straightened and in some places cut some useless steel off.

The next thing we needed was to tack weld the Z bar into place. This was quite the challenge. I tried tacking and it didn’t take. I finally got my weld to hold. I let Grady weld too. His welds would not stick either.

After some frustration we determined that likely we didn’t have a good ground. I put in a lot of effort to get this steel painted so it wouldn’t rust. That unfortunately also prevented us from having a good ground for our welding.

I ground off a lot of paint. This is going to be a problem. The whole reason for the paint is to prevent the damn rust in the first place. So once I get the Z bar in place I’m going to need to paint everything again.

We finally got the Z bar into place and tried to fit the panel. We are about an 1/8 to a 1/4 of an inch off. This is going to require some additional cutting and more fitting to make sure we have it right before we start attaching the braces.

This is part 1 of 2. We spent WAY too much time with welding and prepping. So I cut this down to under 30 minutes.

Like and subcribe.

Thanks for reading and Happy Rovering.

Floor Pan Repair on a Range Rover Classic: Part 2 (Post #681) 12/2/2024

I hope everyone had a wonderful Thanksgiving.

I am back working on the floor bed in this episode. The bottom half of the bed had not had the surface rust ground down. So I turned to and got some grinding done.

I used the wire wheel to get started. There is some use of factory seam sealer. I can’t imagine what the factory was thinking. There is nothing to “seal” on the underside of the truck in the places this was used. Now that I am adding new sides…there is definitely some seams to seal.

Everything will be covered in paint. When the welds get applied there will be some gaps between the new Z bar and the old bed. I’m thinking seam sealer will be helpful to keep water out. I’m also thinking of some sort of wax I could heat up and pour in the gap. I’ll do some additional research but this has possibilities.

I get all the rust off. I also used the sanding disk on some of the more pitted rust. That seemed to work pretty good. These sanding disks are expensive in my opinion. They still might be worth it but I’m not sure.

That’s about it for this week. Next week I’ll be fitting the Z bar and making sure everything will fit in the gaps.

Like and subscribe.

Thanks for reading and Happy Rovering.

Diagnosing Parasitic Draw on a Range Rover Classic: Part 3 (Post #680) 11/25/2024

If you’ve been following along I’ve been trying to find the parasitic draw for quite some time. I finally put my head on straight and dug in.

Having found the circuit that was giving me the trouble it was then time to call in the brains and ask some questions. So I called JagGuy. Mike is a genius and understands more about the physical universe than is possible for most mere mortals.

In our chat he said it about the time the thought was pulling up in the driveway of my mind, “You need to check your relay.” He said he’d look at the schematics (which he said were terrible by the way). It indeed came down to the relay. I have the WRONG relay installed.

I don’t remember when I came up with the fact the OEM relay failed. I do remember bringing it into my house were it sat on my end table and then in the drawer of my end table and then moved to the office? and then lost forever. SO I suspected the relay, I just forgot why.

So back to “the wrong relay” this is the one I had installed…..

What I should have installed was this relay…

You can see the slight difference. The 87a relay has 87a hot. the 87 87 relay is NOT hot all the time. How he came up with that I will never know. What he shared was the 87a relay might be the most common relay in the “relay world”. He has purchased and installed 1000’s of them making his trailer wiring converter boxes for military to civilian service [xm381.com]. He said they are common on fuel injections too if I remember the conversation.

Anyway, he said the far LESS common 87 87 relay is the one I needed. I promptly ordered one from Atlantic British an hour before he texted me back all the great details.

So there you have it. Something as simple as that can disable you. It is good to know that your can use an 87a in a pinch if your 87 87 fails. But you will want to pull it before you park it for any length of time.

UPDATE: The part has arrived and I’m going to test this weekend to confirm by parasitic draw is gone!

Thanks for reading and Happy Rovering.

Diagnosing a Bad Battery on a Range Rover Classic (Post #677) 11/4/2024

A thumbnail.

Yep, you read that right…bad battery. Two weeks ago that battery was fine. It held a charge…or seemed to. But this weekend it decided to cross over to the big battery charger in the sky. The only thing different this week from previous weeks, was I left the battery connected.

I had removed the alternator from the system by pulling the charge cable. So only the rest of the vehicle would be the only thing parasitically draining it. I didn’t think I’d have to work 32 hours out of 48 that 1st weekend, so the experiment was a little skewed.

So when I put the meter on it and it registered 0.00 volts, I was a bit bummed. I they decided I’d try to charge it with trickle charger. I hooked it up and the needle pegged to full. The alligator clips started getting hot. My thought, “That’s not right.”

It wasn’t right. I hauled the battery down to O’Reilly’s and had them test it on their fancy tester. (I need to buy one of these, hmmm….eBay?) It said the terminals were not connected. We guessed a dead cell was shorting it across the terminals. Not sure about that, but they weren’t connected.

So $242.00(US) later…when did batteries start being so expensive? Damn it seems like the last battery I bought for the Big White Bus was like 60 bucks.

So I dropped the battery in and test fired the engine. She fired up no issue.

I also ordered a new negative terminal. The off the shelf ones just suck. I’m going to try the same style my F-150 has. They work pretty well. The only thing left is to put terminals on the three ground cables. I’ll figure that out this weekend.

So next week I’ll test for the vampiric parasitic draw. Check back next week for hopefully some results.

Like and subscribe, donate if you can, Patreon.

Thanks for reading and Happy Rovering.

Floor Pan Repair on a Range Rover Classic (Post #676) 10/20/2024

In this installment I start getting the rust sorted out for the installation of the floor pan. The cross members have quite a lot of rust on them. I used the wire wheel, a flappy sandpaper disk, and even a cutting disk to remove the rust.

The removal went pretty well. It took a few hours. The lip of the floor where the panel was cut out required wire wheel work as well. This was just a LOT of grinding.

I decided to setup and use my sandblasting cabinet. With the new air compressor it worked great. I was really pleased with the result. So much so that I’ll be building a rolling base for it. That way I can store it when I’m not using it and pull it out to make it more convenient. The lamp inside the cabinet has seen better days so I bought a cheap under cabinet lamp that I will install.

At the beginning of the video I briefly reinforce that I still have a parasitic draw. I’m going to experiment with some solution. One, isolating the alternator. I’m still fairly convinced that the alternator’s diode pack has failed. It’s happened before.

Second, I’m going to test for the draw using the “Pull One Fuse While Watching an Amp Meter” method. It takes forever (30 minutes) but should show what’s going on.

There will be a whole video for that.

Thanks for reading, like and subscribe, and as always Happy Rovering.